SP6 Data Acquisition Kit

2,495.00€ – 6,295.00€

Brake Dynamometer DAQ and Controller

New SP6-AWD DAQ version!

The SP-6 dyno controller provides all the necessary hardware and software controliing an engine test bed dynamometer, or rolling road dynamometers.

It implements a Safety Oriented closed loop brake control. It works even without the computer! (with the remote). Available modes: Inertial, Steady, Ramp and Fixed brake (other modes like Road Simulation are implemented in the software)

It is the perfect tool for engine performance testing, ECU calibration, endurance testing, emissions etc.

The new SP6-AWD version provides electronic synchronization between front and rear axles for AWD operation

It is also capable of controlling a 2-HUB and 4-HUB dynamometers using each roller channel for each brake (right and left brakes in the AWD version), and each specific channel (4) in the HUB-4 version.

Features

  • High Speed Ethernet connection
  • Control and monitoring of test engine and brake.
  • Remote control of dynamometer systems (throttle actuator, clutch actuator, gear shift, blowers etc.) from PC software.
  • Provides dual roller + cell channels and brake outputs to support AWD dynamometers, aswell as synchronization between rollers. AWD option needs extra parts as secondary brake power supply, secondary load cell, secondary hall sensor, and AWD Firmware)

What are the differences between SP6 and SP5

  • SP6 has been mainly designed for the HUB-4 application and AWD twin-roller dynos (4 hall sensors), thus it can have up to 4 load cells (2 by default) and has 4 roller inputs, which are useful for some AWD twin-roller dynos
  • SP6 has 8 analog channels instead of 6, and they use a dedicated converter to provide more accuracy (compared with the ADC inside MCU)
  • SP6 has 2 x CANBUS, vs 1 x CANBUS in SP5, to ease adquiring data from CAN sources that work at different speeds (main CANBUS should work only at 250 kbaud)
  • SP6 has an industrial style and eases some installations, specially inside an electric cabinet

Installation: Installation and Setup Manual

Software: SportDyno 4.0 Features, Download

*Prices do not include VAT

What does SP6 kit include?

  • 1 x SP6 Data Aquisition unit
  • 1 x Hall Sensor, for roller / brake speed
  • 1 x Capacitive and Inductive clamps, for Engine RPM
  • 1 x Load Cell (several sizes available, see below)
  • 1 x Brake Power Supply (several voltages and currents available, see below)
  • 1 x SP6 to PWS cable adapter
  • 1 x Installation cables: Hall sensor extension, Serial Cable
  • 1 x USB to Serial adapter, with FTDI chip for the best compatibility
  • 1 x Geartooth and braket (new)

AWD Version:

  • AWD sync FW activation
  • 2 x Hall Sensor, for roller / brake speed
  • 2 x Load Cell
  • 2 x Brake Power Supply

HUB-4 Version:

  • HUB-4 sync FW activation
  • 4 x Hall Sensor, for roller / brake speed
  • 4 x Load Cell
  • 4 x Brake Power Supply

What SP6 Kit does NOT include?

  • Other sensors apart from hall and load cell: Lambda, Weather Station, Pressure sensors, etc
  • Other Interfaces: OBDII, xDS (SDS, HDS, KDS)
  • Roller
  • Eddy current brake
  • Relays
  • Cooling Fans
  • VFDs (Variable Frequency Drive)
  • Dyno frame

Specifications

Input Specifications

  • 4 x Brake/Roller speed input
  • 1 x Engine Rpm Speed input (Capacitive and Inductive clamps)
  • 8 x Analog inputs (0-5v)
  • 8 x Thermocouple (type-k) Inputs
  • 4 x Load Cell input (16/24 bit accuracy and digital zero and gain adjust)
  • 1 x Pulse Counter Input (Ex. detonation counter)
  • 1 x Run/Stop Button (same as SP1)
  • 1 x Panic Button (Emergency Stop)

Output Specifications

  • 4 x PWM Brake Control Signal
  • 8 x Digital Outputs (12V Relays)
  • 1 x Air Speed Output (PWM 0-5v)
  • 1 x Servo output / Throttle (PWM 0-5v or RC pulse)

Connectivity Specifications

  • 2 x RS232 DB9 Connector
  • 1 x Ethernet RJ45 Connector
  • 2 x CANBUS (focused on PWS control, but there are free channels for other data, no license is required)
  • 1 x Internal Bluetooth (available under request)

Test/Control modes

  • RPM Constant (engine speed)
  • Ramp Test (programmable slope)
  • Sequenced/Programmed Test
  • Step Test
  • Road Simulation (future version)

Installation

Rolling Road and HUB Dynos

SP6 Can be used on several types of rolling road and HUB dynamometers:

  • Motorcycle (single roller)
  • Car, 1 axle, single roller per wheel (or long single roller)
  • Car, 1 axle, twin roller per wheel (brake is mounted on the front rollers)
  • Car, 2 axle, single or twin roller per wheel, but only one axle at once
  • AWD Car and HUB-2: 2 axle, both axles operating at once. NOTE: this option has an extra cost!
  • AWD Car, twin-roller with 4 sensors: 2 axle / twin-roller, each subaxle has a sensor (4)
  • HUB-4: 4 brakes, all brakes operating at once. NOTE: this option has an extra cost!
  • Other dynos based on rollers, with a maximum of 2 speed sensors

Engine Testbed Dyno

Part List for a complete Engine Testbed installation:

  • SP6 unit. It can work stand alone or with the computer.
  • Computer. Win98, ME, 2000, XP, Vista, Win7, Win8.1.
  • Hall Effect Sensor. Included with SP6.
  • Gear Tooth. Installed on the eddy current brake to read its speed. For example 8 teeth.
  • Load Cell. It depends on the engine, typical values are 500 kg for bike engines and 1000 kg for cars, but it must be calculated.
  • Eddy Current Brake. 192 volt rated, it size depends on the application.
  • Power supply: Sportdevices control module + SCR & diode pack.
  • Throttle Servo (optional). A high torque RC servo can be used to drive the throttle.
  • Ignition and Starter Relays. 12 volt relays to control the engine. Additional relays can be installed on the SP6 to control the fans on the room.
  • Fans / Turbines. Some type of fans or turbines are needed to next functions:
    • Feed the air intake with fresh air from outside the room (inner air gets hot quickly) this turbine should be very high power (>2 KW, or >5KW) and high speed to simulate on-track conditions, a variable speed driver is recommended + frequency to voltage converter to use the brake speed.
    • Exhaust extraction, the pipes should be made with iron or steel because the high temperature of exhaust gas.
    • Engine coolant, water should by couled by a fan, a car’s fan or a truck’s fan can be used with a thermostat to ensure the water will be at a right temperature.
    • Engine and exhaust pipes cooling, when runing on the track the exhaust pipes are being cooled as the vehicle runs, but when working on the dyno they may get too hot and can be damaged. Certaint exhaust pipes can not work at high temperatures (for example: titanium)
  • Variable speed driver. It is recommended for air-intake turbine.

What implements

  SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4
Roller Channels 1 2 4
Engine Channel 1 1 1
Analog Channels (0-5V) 4 6 8
Thermocouples (K) 2 8 8
Counter input (knock) 1 1 1
Load Cell Channels 0 / 1 (24 bit) 2 (24 bit) 2 / 2 / 4 (24 bit)
Brake Outputs – / 1 2 4
Servo Output 1 RC* 1 RC or PWM 1 RC or PWM
Airspeed Output – / 1 PWM 1 PWM 1 PWM
Relay Outputs – 8 8
Speed Control (PID) – / 1 2 / 2 + sync 2 / 2 + sync / 4 + sync
RS232 1 1 2
Bluetooth 1 1* 1*
Ethernet – 1 1
CANBUS – 1 2
KIT Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495
DAQ Price 870 / 1195 2295 2795

What contains

  SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4 Price
Hall sensor 1 1 / 2 1 / 2 / 4  80€
Capacitive Clamp 1 1 1  60€
Inductive clamp – / 1 1 1  80€
Load Cell – / 1 1 / 2 1 / 2 / 4  150€
Brake Power Supply – / 1 1 / 2 1 / 2 / 4  650€
USB-Serial 1 1 1  25€
Power Cord 1 1 1  10€
Ground Cable 1 1 1  10€
Pendrive 1 1 1  
Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495  

Accesories

All rights reserved © 2000 – 2023 SportDevices
Facebook Instagram