SP1+ V5 Low Cost Braked Dyno Electronic Kit

1,195.00€ – 1,995.00€

Low Cost Software and electronics kit for Braked Dyno.
(Includes 16T geartooth)

Features

  • Fast 32-bit MCU
  • Includes a Load Cell 24 bit Converter and a digital filter (more than 300 Samples Per Second)
  • Safety Oriented closed loop brake control. It works even without the computer! (with the remote). Available modes: Inertial, Steady, Ramp and Fixed brake (other modes like Road Simulation are implemented in the software)
  • 1 Roller input and 1 Engine input (100 MHz clock)
  • 1 Brake Output (PWM)
  • 4 analogue inputs (12 bit)
  • 2 thermocuple inputs (16 bit)
  • The kit includes our PWS3.3 up to 40A and load cell in order to provide a full low cost solution for single axle and engine dynos
  • Connection is done by using our dedicated Serial USB cable (USB chip is only inside the USB connector side to improve noise immunity)
  • Realtime graphs display

Software: SportDyno 4.0 Features, Download

(Price for DAQ only: 1195€)

*Prices do not include VAT

What does include

  • SP1+ data acquisition unit (V5) (11 input channels, and 2 outputs):
    • 1 Roller RPM input
    • 1 Engine rpm input
    • 1 Load Cell input (internal 24 bit, scaled to 16)
    • 2 thermocouple type K input (up to 1000°C)
    • 4 general analog inputs
    • 1 counter input
    • 1 Brake Output (PWM)
    • 1 servo output
  • Hall Effect Digital Sensor for measuring roller speed
  • PWS3.3 up to 40A
  • Load Cell:150, 300, 450, 1000 kg (other models available under request)
  • Geartooth and braket (new)
  • Dedicated Serial USB cable to improve noise immunity
  • Installation cables and SportDyno software

Connection is done by using our dedicated Serial USB cable (USB chip is only inside the USB connector side to improve noise immunity).

The equipment is completed with a modern Software for Windows, very powerful and easy to use. It allows to work simultaneously with several tests.

Specifications

Power input: 85-230V 50Hz/60Hz

Load Cell input: recommended 2mV/V and 3mV/V type

Data connection 115200 baud RS232C (DB9 Conn). The kit includes a dedicated COM-USB cable

Roller RPM input connector (CN2)

  • Type of sensor: Hall Effect active sensor (doesn’t need external magnets)
  • Type of input: logical Level (active at high level)
  • Maximum frequency: 18 KHz (6,700 RPM with 180 teeth)
  • Maximum cable length: 10 m
  • (Optional) Run/Stop input SWITCH

Engine RPM Capacitive Input: capacitive type (reads high voltage pulses on ignition cables)

Display: LCD 16×2 Characters.

Installation

CN1-additional engine RPM input, 0 to 5 volt. Suitable for ECU output, or external adaptors.

CN2-Roller Speed Sensor (Hall Effect), Switch input and Brake PWM Output

CN3-Load Cell

CN4-Digital Counter and Servo output

CN5-Analog connector, Analog channels 1 and 3 (J and L), from 0 to 5 volt, suitable for Wideband Oxigen Sensor

CN6-Analog connector, Analog channels 2 and 4 (K and M), from 0 to 5 volt, suitable for Wideband Oxigen Sensor

WHAT IMPLEMENTS

SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4
Roller Channels 1 2 4
Engine Channel 1 1 1
Analog Channels (0-5V) 4 6 8
Thermocouples (K) 2 8 8
Counter input (knock) 1 1 1
Load Cell Channels 0 / 1 (24 bit) 2 (24 bit) 2 / 2 / 4 (24 bit)
Brake Outputs – / 1 2 4
Servo Output 1 RC* 1 RC or PWM 1 RC or PWM
Airspeed Output – / 1 PWM 1 PWM 1 PWM
Relay Outputs – 8 8
Speed Control (PID) – / 1 2 / 2 + sync 2 / 2 + sync / 4 + sync
RS232 1 1 2
Bluetooth 1 1* 1*
Ethernet – 1 1
CANBUS – 1 2
KIT Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495
DAQ Price 870 / 1195 2295 2795

WHAT CONTAINS

SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4 Price
Hall sensor 1 1 / 2 1 / 2 / 4  60€
Capacitive Clamp 1 1 1  30€
Inductive clamp – / 1 1 1  80€
Load Cell – / 1 1 / 2 1 / 2 / 4  150€
Brake Power Supply – / 1 1 / 2 1 / 2 / 4  650€
USB-Serial 1 1 1  25€
Power Cord 1 1 1  10€
Ground Cable 1 1 1  10€
Pendrive 1 1 1
Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495
All rights reserved © 2000 – 2023 SportDevices
Facebook Instagram